Product ID:ENAMEL, INTERIOR, NONFLAMING (DRY), CHLORINATED ALKYD RESIN,
MSDS Date:08/01/2000
FSC:8010
NIIN:01-344-5094
Status Code:A
MSDS Number: CLFYB

STIC-ADHESIVE PRODUCTS CO, INC

3950 MEDFORD STREET
LOS ANGELES, CA 90063

Emergency Phone: 999-999-9999

Info Phone: 213-268-2956

Preparer: ERNEST CARTER

Cage: DO670

STIC-ADHESIVE PRODUCTS CO, INC

LOS ANGELES, CA 90063

Telephone: 213-268-2956

Cage: DO670

TITANIUM DIOXIDE

CAS: 13463-67-7

RTECS: XR2275000

OSHA PEL 15 MG/M3

ACGIH TLV: 10 MG/M3

ZINC PHOSPHATE

BARIUM METABORATE

CHLORENDIC ALKYD

PAINT THINNER

CAS: 8052-41-3

RTECS: WJ8925000

OSHA PEL 2900 MG/M3;500 PPM

ACGIH TLV: 525 MG/M3;100 PPM

DRIVERS LEVELING AGENT

CAS: 136-52-7

ANTISKINNING AGENT THIXATROPIC AGENT

Routes of Entry: Inhalation:YES Skin:YES Ingestion:YES
Health Hazards Acute and Chronic:INGESTION: KEEP PERSON WARM, QUIET AND
GET IMMEDIATE MEDICAL ATTENTION. EYE CONTACT: CAUSES SEVERE EYE
IRRITATION. SKIN CONTACT: CAUSED PRIMARY SKIN IRRITATION. MAY BE
HARMFUL IF ABSORBED THROUGH THE SKIN. INHALATION: VAPOR AND SPRAY
MIST HARMFUL IF INHALED. VAPOR IRRITATES EYES, NOSE, THROAT. MAY
IRRITATE LUNGS. AVOID LONG TERM OR REPEATED CONTACT. PRODUCT
CONTAINS TITANIUM DIOXIDE.
Effects of Overexposure:EYE WATERING, HEADACHES, NAUSEA, DIZZINESS, AND
LOSS OF COORDINATION ARE INDICATION THAT SOLVENT LEVELS ARE TOO
HIGH. REDNESS, ITCHING, BURNING SENSATION AND VISUAL DISTURBANCES
MAY INDICATE EXCESSIVE EYE CONTACT, DRYNESS, ITCHING, CRACKING,
BURNING, REDNESS, AND SWELLING ARE CONDITIONS ASSOCIATED WITH
EXCESSIVE SKIN CONTACT.

First Aid:INGESTION: IF SWALLOWED, GIVE 1 OR 2 GLASSES OF WATER, BUT DO
NOT INDUCE VOMITING. EYE CONTACT: FLUSH EYES IMMEDIATELY WITH
PLENTY OF WATER FOR AT LEAST 30 MINUTES. SKIN CONTACT: FLUSH
IMMEDIATELY WI TH PLENTY OF WATER FOLLOWED BY WASHING WITH SOAP AND
WATER. INHALATION: IF AFFECTED BY INHALATION OF VAPORS OR SPRAY
MIST, REMOVE TO FRESH AIR. INGESTION, ANY TYPE OF OVEREXPOSURE OR
SYMPTOMS OF OVERE XPOSURE OCCURS DURING OR FOLLOWING THE USE OF
THIS PRODUCT.

Flash Point Method:TCC
Flash Point:=40.6C, 105.F
Autoignition Temp:Autoignition Temp Text:NONE
Lower Limits:NONE
Upper Limits:NONE
Extinguishing Media:USE NATIONAL FIRE PROTECTION ASSOCIATION (NFPA)
CLASS B EXTINGUISHERS (CARBON DIOXIDE, DRY CHEMICAL, OR UNIVERSAL
AQUEOUS FILM FOAMING FOAM) DESIGNED TO EXTINGUISH NFPA CLASS.
Fire Fighting Procedures:WATER SPRAY MAY BE INEFFECTIVE. WATER SPRAY
MAY BE USED TO COOL CLOSED CONTAINERS TO PREVENT PRESSURE BUILD UP
AND POSSIBLE AUTOIGNITION OF EXPLOSION WHEN EXPOSED TO EXTREME
HEAT. IF WATER IS USED, FO G NOZZLES ARE PREFERABLE.
Unusual Fire/Explosion Hazard:KEEP CONTAINERS TIGHTLY CLOSED. ISOLATE
FROM HEAT, ELECTRICAL EQUIPMENT, SPARKS, AND OPEN FLAMES. CLOSED
CONTAINERS MAY EXPLODE WHEN EXPOSED TO EXTREME HEAT.

Spill Release Procedures:PROVIDE MAXIMUM VENTILATION. ONLY PERSONNEL
EQUIPPED WITH PROPER RESPIRATORY AND SKIN AND EYE PROTECTION SHOULD
BE PERMITTED IN THE AREA. REMOVE ALL SOURCES OF IGNITION. TAKE UP
SPILLED MATERIAL WITH SAWDUST, VERICULITE, OR OTHER ABSORBENT
MATERIAL AND CONTAINERS SHOULD BE RECYCLED OR DISPOSED OF THROUGH
AN APPROVED WASTE MANAGEMENT FACILITY.

Handling and Storage Precautions:DO NOT STORE ABOVE 120 DEGREES F.
STORE LARGE QUANTITIES IN BUILDING DESIGNED AND PROTECTED FOR
STORAGE OF NFPA CLASS IC FLAMMABLE LIQUIDS.
Other Precautions:IF THIS MATERIAL IS PART OF A MULIPLE COMPONENT
SYSTEM, READ THE MATERIAL SAFETY DATA SHEET(S) FOR THE OTHER
COMPONENTS BEFORE BLENDING AS THE RESULTING MIXTURE MAY HAVE THE
HAZARDS OF ALL OF ITS PART S.

Respiratory Protection:(NIOSH/MSHA APPROVED AIR PURIFYING OR AIR
SUPPLIED RESPIRATORS MAY ALSO REDUCE EXPOSURE.
Ventilation:PROVIDE GENERAL DILUTION OR LOCAL EXHAUST VENTILATION IN
VOLUME AND PATTERN.
Protective Gloves:WEAR IMPERMEABLE CLOTHING SUFFICIENT TO COVER EXPOSED
SKIN SURFACES CONSTRUCTED
Eye Protection:WEAR CHEMICAL TYPE SPLASH GOGGLES OR FULL FACE SHIELD.
Other Protective Equipment:CLEAN OR DISCARD CONTAMINATED CLOTHING AND
SHOES.
Work Hygienic Practices:NONE
Supplemental Safety and Health
NONE

Boiling Pt:=154.4C, 310.F
Melt/Freeze Pt:M.P/F.P Text:NONE
Decomp Temp:Decomp Text:NONE
Vapor Pres:2.000 MMHG AT 68 F
Vapor Density:4.9
Spec Gravity:1.62-1.65
Appearance and Odor:NONE

Stability Indicator/Materials to Avoid:YES
AVOID CONTACT WITH STRONG ALKALIS, STRONG MINERAL ACIDS, OR STRONG
OXIDIZING AGENTS.
Stability Condition to Avoid:AVOID CONTACT WITH STRONG ALKALIS, STRONG
MINERAL ACIDS, OR STRONG OXIDIZING AGENTS.
Hazardous Decomposition Products:NONE

Waste Disposal Methods:WASTE MATERIAL MUST BE DISPOSED OF IN ACCORDANCE
WITH FEDERAL STATE, PROVINCLAL, AND LOCAL ENVIRONMENTAL CONTROL
REGULATIONS.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.